• Rad Optimux 106

1 Optimux-XLT1 Multiple T1 and Ethernet Multiplexer Installation and Operation Manual Notice This manual contains information that is proprietary to RAD Data Communications. No part of this publication may be reproduced in any form whatsoever without prior written approval by RAD Data Communications. No representation or warranties for fitness for any purpose other than what is specifically mentioned in this manual is made either by RAD Data Communications or its agents. For further information contact RAD Data Communications at the address below or contact your local distributor. International Headquarters RAD Data Communications Ltd. 24 Raoul Wallenberg St.

Tel Aviv Israel Tel: Fax: U.S. Headquarters RAD Data Communications Inc. 900 Corporate Drive Mahwah, NJ USA Tel: (201) Toll free: Fax: (201) RAD Data Communications Publication No /0123 Warranty This RAD product is warranted against defects in material and workmanship for a period of one year from date of shipment. During the warranty period, RAD will, at its option, either repair or replace products which prove to be defective. For warranty service or repair, this product must be returned to a service facility designated by RAD. Buyer shall prepay shipping charges to RAD and RAD shall pay shipping charges to return the product to Buyer. However, Buyer shall pay all shipping charges, duties and taxes for products returned to RAD from another country.

Limitation of Warranty The foregoing warranty shall not apply to defects resulting from improper or inadequate maintenance by Buyer, Buyer-supplied firmware or interfacing, unauthorized modification or misuse, operation outside of the environmental specifications for the product, or improper site preparation or maintenance. Exclusive Remedies The remedies provided herein are the Buyer s sole and exclusive remedies.

Rad Optimux 106

RAD shall not be liable for any direct, indirect special, incidental, or consequential damages, whether based on contract, tort, or any legal theory. Safety Warnings The exclamation point within a triangle is intended to warn the operator or service personnel of operation and maintenance factors relating to the product and its operating environment which could pose a safety hazard. Always observe standard safety precautions during installation, operation and maintenance of this product. Only a qualified and authorized service personnel should carry out adjustment, maintenance or repairs to this instrument. No adjustment, maintenance or repairs should be performed by either the operator or the user. Laser Warnings This product may be equipped with a laser diode. In such a case, this laser warning symbol label will be attached near the optical transmitter.

Please observe the following precautions: Do not attempt to adjust the laser drive current. Do not use broken or unterminated fiber-optic cables/connectors or stare at the laser beam. The use of optical equipment with this product will increase eye hazard.

Use of controls, adjustments or performing procedures other than those specified herein, may result in hazardous radiation exposure.4 Telecommunication Safety The safety status of each of the ports on the Optimux-XLT1 is declared according to EN and is detailed in the table below: Ports Safety Status LAN, ALARM SELV Circuit operating with Safety Extra-Low Voltage T1 TNV-1 Circuit whose normal operating voltage is within the limits of SELV, on which overvoltages from Telecommunications Networks are possible. Note The T1 ports are not intended for connection to exposed plant. Regulatory Information FCC-15 User Information This equipment has been tested and found to comply with the limits of the Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to the radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Warning per EN This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.5 Contents Chapter 1.

Introduction 1.1 OVERVIEW Versions Applications Features PHYSICAL DESCRIPTION Front Panel Rear Panel FUNCTIONAL DESCRIPTION Fiber Optic Link Interface Link Redundancy Tributary Interface Characteristics Management Requirements Timing Power Requirements TECHNICAL SPECIFICATIONS Chapter 2. Installation and Setup 2.1 INTRODUCTION SITE REQUIREMENTS & PREREQUISITES PACKAGE CONTENTS INSTALLATION AND SETUP Identifying Optimux-XLT1 Modules Setting Internal Jumpers and Switches INTERFACES AND CONNECTIONS Channel Connections Fiber Optic Link Connections Alarm Connection Management Connections Power Connection Chapter 3.

Operation 3.1 OPTIMUX-XLT1 CONTROLS Front Panel Controls Rear Panel Controls OPERATING INSTRUCTIONS Turn ON Normal Indications Redundancy Functions Turn OFF Chapter 4.

RAD-1800NG Pneumatic Torque WrenchThe RAD 1800NG pneumatic torque wrench has the highest weight to power ratio in it's class. RAD 1800NG torque wrenches are used worldwide in such service industries as mining, petro-chemical, railroad and construction. The RAD 1800NG is ideal for heavy duty bolting applications anywhere that 1' or 1.5' impact wrenches are being used. PATENTED planetary gear reduction drive system delivering one of the highest power-to-weight ratios of any pneumatic controlled bolting system. Smooth continuous flow of controlled torque eliminating destructive hammering. Lightweight ergonomic pistol grip design reducing operator strain and injury; resulting in increased productivity.

Controlled torque – accuracy of +/-5%, and repeatability of +/-2%RAD 1800NG Classic Series.